Be sure to review the Notes below before upgrading! This release - includes a new version of the Scomm32 serial port control that works correctly at 115,200 baud - when setting or clearing dual watch for an IC7800, IC7850, or IC7851, sends only one CI-V command per command interval - on startup, reliably displays active DX stations on the Bandspread window (tnx to Björn SM7IUN) - when changing memory banks with memory notes displayed, correctly updates the Sel button tooltips (tnx to Brian N5BCN) - saves the Yaesu "Filter Group Data File" pathname to the Windows Registry when the Select or Save functions are activated (tnx to John N4DSP) - enables the Yaesu "Filter Group Data File" Save button when the a new Filter Group is added or deleted (tnx to John N4DSP) - restores the ability to delete an entry in a frequency-dependent device table by selecting the entry and striking the Delete key (tnx to Björn SM7IUN) - when controlling a Yaesu FTDX1200 or FTDX3000, enables the Filter panel's Width slider to select and display 2400 Hz when in CW mode (tnx to Mike K2CD) - when pushing a frequency and mode onto a band stack, pushes the correct mode (tnx to Tim NZ8J) - changes the shortcut for resetting the connection to the Primary Transceiver to depressing the CTRL and SHIFT keys while clicking the Main window's Config button (tnx to Björn SM7IUN) - supports the "memory channel" in Kenwood radios - when controlling an Icom radio, illuminates a "CI-V" alert indicator on the Main window when the radio reports a CI-V bus collision - supports the Icom IC-7610 (tnx to Tim NZ8J) - optionally displays a Spectrum-Waterfall window with active DX stations when controlling a properly connected and configured Icom IC-7300, IC-7610, IC-7850, and IC-7851 (tnx to Björn SM7IUN, Tim NZ8J, Art W2NRA, CJ WT2P, Jay W5JAY, Ron KF5JRA, Rick WA7BNG, Tom N1MM, and Icom's Ray N9JA) - provides primary transceiver selection-by-band for 23cm - supports the Flex 6400 and 6600 (tnx to Flex's Eric KE5DTO) - if a frequency-dependent device is disabled, invoking in a Command Sequence loads the device's data from the "Data File" pathname specified on the device's tab on the Configuration window (tnx to Björn SM7IUN) - adds the Spectrum-Waterfall.jpg documentation file and updates the ChangingBandwidth.htm, ChangingFrequency.htm, CommandSequences.htm, Configuration.htm, and index.htm documentation files Notes: 1. Before upgrading, terminate Commander, DXView, SpotCollector and WinWarbler 2. Update your firewall and anti-malware applications to consider this new version of Commander to be "safe" 3. If Commander is controlling an Icom IC-7300, IC-7610, IC-7850, or IC-7851 using a direct USB connection configured for 115,200 baud, you can enable the new Spectrum-Waterfall window by checking the "Spectrum-Waterfall window" box in the upper-left corner of the Configuration window's Bandspread tab 3a. reference documentation for the Spectrum-Waterfall window is available in http://www.dxlabsuite.com/commander/Help/ChangingFrequency.htm#Changing_frequency_via_the_Spectrum-Waterfall_window 3b. a screen shot of the Spectrum-Watefall window is available in http://www.dxlabsuite.com/commander/Help/Spectrum-Waterfall.jpg 3c. if your Icom IC-7300, IC-7610, IC-7850, or IC-7851 is connected to your computer using a USB connection configured for 115,200 baud, you can display new Spectrum-Waterfall window by depressing the CTRL key while clicking the Bandspread button on Commander's Main window 4. If this upgrade doesn't work correctly, see the "After an Upgrade" section of 5. After upgrading, to revert to the previous version of Commander, see Commander 13.0.8 is available via the DXLab Launcher and via 73, Dave, AA6YQ